7:56 AM | Posted in

A high-torque, insulated electric motor, usually rated at 200–750 watts (¼ to 1horsepower) for a domestic unit, spins a circular turntable mounted horizontally above it. Induction motors rotate at 1,400–1,800 rpm and have low starting torque;commutator motors rotate at higher speeds (about 2,800 rpm), have high starting torque, and are usually lighter. However commutator motors are noisier than induction motors, partially due to the higher speeds and partially because the commutator brushes rub on the slotted armature. The higher starting torque of those appliances with a permanent magnet motor secures in most cases that there will be no blockage.

The added weight and size of induction motors might be of concern. Many models have some degree of sound insulation.

The turntable is surrounded by a shredder ring, which has sharp slots. The food waste sits on the turntable and through centrifugal force is forced to its perimeter and through the shredder ring. The turntable has a number of swiveling lugs—similar to little hammers attached to its topside—which assist in forcing the waste through the shredder. Except for special models, most of the food waste disposers do not have any sharp blades or scissors.

A garbage disposal from above; the grinding chamber can be seen when it is removed from the sink.

Waste is fed into a chamber above the turntable and drops on the turntable. The chamber may have a rubber partial closure through which waste can be pushed without letting cutlery and other objects fall in, but essentially the chamber is open at the top, and there is access to the turntable. This is useful in the case of a jam: The turntable can be forced round by pushing with a wooden spoon handle or similar object until the jam clears. Waste that cannot be ground successfully can be removed manually.

Most units are of the continuous-feed type, allowing waste to be added as the unit runs. Batch-feed models are also available with a lid that must be locked before operation, making it impossible to run the machine when a user is trying to clear a jam by hand and preventing cutlery, etc. from falling in.

Some commercial and high-end domestic disposals also have an under-cutter blade that revolves below the turntable and chops the ground waste, including fibrous material which could cause a drain clog, finer. These disposals can handle fibrous waste such as artichoke leaves and corn husks that cannot be successfully ground in a standard disposal.

Waste disposal units may jam but can usually be cleared either by forcing the turntable round from above or by turning the motor using a hex-key wrench inserted into the motor shaft from below. Very hard objects accidentally or deliberately introduced, such as metal cutlery, can damage the waste disposal unit and become damaged themselves. More problematic are drain blockages caused by shredded waste that is fibrous (artichoke leaves) or starchy (potato peelings).

Some higher-end units have automatic reversing. By using a slightly more-complicated centrifugal stating switch , the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams but is claimed to be unnecessary by some manufacturers: Since the late 1970s most disposal units have swivel impellers which make reversing unnecessary.

Another kind of garbage disposal unit is powered by water pressure rather than electricity and does not pose an electrical hazard. Instead of the turntable and grind ring described above, an alternative machine has a water-powered unit with an oscillating piston with blades attached to chop the waste into fine pieces. Because of this cutting action, they can handle fibrous waste. Water-powered units take longer than electric ones for a given amount of waste and need fairly high water pressure to function properly.

Cold water should always be kept running when the disposal is switched on to prevent damage to the blades and wash away the chopped waste without allowing it to build up and clog the drains. Hot water tends to melt easily-flushed solid shredded pieces of fat, which can then solidify and block the drain. Under no circumstances should oil or grease be disposed in a sink drain – with or without a disposer in use.

Provision must be made to supply and switch power to the waste disposal unit. A conventional electrical switch can be used, which requires wiring to be installed and poses a potential electrical shock hazard if used with wet hands. An air switch which delivers a puff of air to operate an electric switch remote from the operator is safer. Alternatively, a wireless remote control switch can be used.

If a garbage disposal is discovered to have a "frozen lug", or a hammer that does not move freely, it is recommended that the user feed smaller bones such as those from chicken, through the unit. As seen on an episode of the TV show How It's Made, In Sink Erator company tests its units by feeding frozen steer bones through a sample batch of disposal units, so one does not need fear damage to a unit in good condition with chicken bones. Many repair technicians recommend a weekly feeding of a batch of ice cubes through a running disposer to maintain good cleanliness. This will assist in keeping the lugs or hammers rotating freely and remove any build-up of deposits and minerals. Never feed glass into a garbage disposal.

A common issue I find with the insallation of a GD is the wires enter from the bottom of the unit without the proper wire connector. At times I have even find the unit ungrounded!


www.homeinspectionservices.org
Category:
��
7:52 AM | Posted in

The garage door is the largest moving object in a home. An improperly adjusted garage door opener can exert strong and deadly forces and might not reverse the garage door in an emergency. The garage door counterbalance springs should be properly adjusted in order for the safety reverse system to function properly. Thus, proper installation and maintenance are extremely important in order for the garage door and garage door opener to operate smoothly and safely.

The header bracket, which attaches the front end of the opener track to the header wall, must be securely attached to the structural members of the garage wall. If not, the opener might not reverse the garage door in an emergency. The rail can also pull away from the wall.

All garage door openers manufactured since 1982 are required to provide a red handle attached to a red rope that attaches to the trolley that allows for the garage door to be disconnected from the garage door opener in the event of entrapment. The handle should be mounted no higher than six feet from the ground. Homeowners should be familiar with this mechanism. Garage door openers manufactured since 1982 are also required to reverse the garage door if it strikes a solid object.

The wall console/push button should be mounted at least five feet from the floor and the remote controls should be kept out of the hands of children. Children should never be allowed to play with or use the garage door opener remotes or wall push-buttons. Homeowners should also keep a moving door in sight until it fully opens or closes.

By federal law, garage door openers manufactured since 1993 are required to have safety sensors on both sides of the garage door mounted no higher than six inches above the ground that emit an invisible laser beam across the door. The garage door opener is required to reverse the door to the open position if the beam is broken.


www.homeinspectionservices.org
Category:
��
7:43 AM | Posted in

Contrary to popular belief, the electric opener does not provide the actual lifting power to open and close a heavy garage door. Instead, the actual lifting power comes from the counterbalance springs that are under tension to lift the garage door via steel counterbalance cables.

The electric opener itself consists of a power unit that contains the electric motor. The power unit attaches to a track. A trolley connected to an arm that attaches to the top of the garage door slides back and forth on the track, thus opening and closing the garage door. The trolley is guided along the track by a chain, belt, or screw that turns when the motor is operated. A red handle and rope are attached to the trolley to allow the garage door to be disconnected from the opener for manual operation or in case of emergency. Limit switches on the power unit control the distance the garage door opens and closes once the motor receives a signal from the remote control or wall push button to operate the door. Many safety devices are available and required to insure safe operation from day to day. It is imperative that you test the safety of the reverse switch and optic eyes during a home inspection.

The entire assembly hangs above the garage door. This assembly should also be inspected for installation issues. The power unit hangs from the ceiling and is located towards the rear of the garage. The end of the track on the opposite end of the power unit attaches to a header bracket that is attached to the header wall above the garage door. The power head is usually supported by punched angle iron.


www.homeinspectionservices.org
Category:
��
7:36 AM | Posted in

Although molds grow on dead organic matter everywhere in nature, their presence is only visible to the unaided eye when mold colonies grow. A mold colony does not comprise discrete organisms, but an interconnected network of hyphae called amycelium. Nutrients and in some cases organelles may be transported throughout the mycelium. In artificial environments like buildings, humidity and temperature are often stable enough to foster the growth of mold colonies, commonly seen as a downy or furry coating growing on food or other surfaces.

Some molds can begin growing at temperatures as low as 2°C. When conditions do not enable growth, molds may remain alive in a dormant state depending on the species, within a large range of temperatures before they die. The many different mold species vary enormously in their tolerance to temperature and humidity extremes. Certain molds can survive harsh conditions such as the snow-covered soils of Antarctica, refrigeration, highly acidic solvents, and even petroleum products such as jet fuel. Some molds use the humidity in the air as their only water source; other molds need more moisture.

You can not get rid of the mold in your house by taking out the drywall patching it up and painting it. You have got to find the source of the moisture.


www.homeinspectionservices.org

Category:
��