Showing posts with label Home DIY. Show all posts
Showing posts with label Home DIY. Show all posts
8:33 PM | Posted in

Can I Test For Mold Myself?:

Yes, most home supply stores have do-it-yourself mold testing kits readily available. These kits can be used to test the air quality in your home. Although not a substitution for professional inspections they can be used in between professional inspections allowing for more time between the more costly professional inspections.

Essential Preventative Measures: The most essential preventative measures may sound like common sense. They include but are not limited to: ridding your home of any standing water, scrubbing appliances (like refrigerators, humidifiers, etc) with antibiotic soap, cleaning your AC unit regularly, regularly changing your floor mats and shower curtains.

As you can see, conducting routine mold inspections should become a part of your routine home maintenance schedule. If left unchecked, mold can cause enormous issues with not only your health but you home as well.

Taking care of your health is never too important. By cleaning up mold you will improve the health of you and your family in your home.

www.homeinspectionservices.org
Category:
��
6:38 PM | Posted in
Removing Oil-based Makeup:

The household trick for removing oil-based make-up is to use a "pre-wash stain remover" and spray it directly onto the stain. Do not rub the stain! Let the solution soak into the carpet, as most chemicals take some time (Lipstick and Mascara will need more time). After the solution has had time to soak, rinse the stain with warm water and dab the stain (remember do not rub). The stain should be faded or completely gone.

If not, repeat the process. Another option is to use a stronger household detergent. Typically, the more expensive detergents will be best to use in this case. These detergents typically have more punch to remove those tougher stains. If the detergent process does not remove the stain then you can try rubbing alcohol. Use the same process as above and remember not to rub the stain! Let it soak and then rinse with warm water and dab.

The longer you leave the stain untreated, the harder it will be to remove.

Removing Fingernail Polish

Fingernail polish stains are tough to remove and can only be removed with a chemical. Removing these stains takes some patience and skill. The best product to use is an acetone based fingernail polish remover. You should test the acetone on your carpet before you try this process. Good test spots are in a closet or somewhere that is not noticeable. When testing, place a small amount of acetone on your test area and let it sit for a few minutes. Then remove the acetone by blotting it out with a white towel. If there are no imperfections made from the acetone onto your test spot, you'll now want to treat the stain directly.

You should use a dropper to apply the polish remover to the stain. Let the chemical soak, but not too long (most acetone based polish removers evaporate quickly). You should only let it sit long enough so that the polish starts to run. Then blot it with a white towel. The fingernail polish should lift off onto the towel and stain should be lightened. If the stain remains try the process again. Your last resort is to make a trip to your local store where they sell products that may work better. Be sure to follow the instructions carefully. With these types of stains I recommend contacting a professional carpet cleaning service.

www.homeinspectionservices.org
Category:
��
1:13 PM | Posted in
What to Expect

Gaps or voids in any insulation material, account for significantly poorer thermal performance, so proper installation is important.

Wall insulation is more complicated to install than attic or underfloor insulation. It's best to contact a professional insulation contractor. A professional has the experience to work efficiently, effectively, and recognize unexpected problems.

An experienced crew with good equipment can insulate the walls of an average house from start to finish in less than one day. One crew member drills the wall cavities and probes for blocking. Another follows with the nozzle and hose from the blowing machine and fills the cavity with insulation. An ordinary wall section that is 8 feet in height requires two holes, one about 12 inches below the drop of the wall and the other one up about 36 inches from the bottom of the wall. A wall 10 feet in height may need three holes to achieve adequate compaction of the insulation throughout the cavity (depending on the equipment).

After the installation, the holes are plugged with a wood or plastic plug. The plug is painted if the homeowner supplies the paint. Another option includes a plug with spackle over it. Most insulation contractors stress this is not a finished job and matching colors and textures is not their specialty. Plugs installed without adhesive may work their way out over time because of changing moisture content and temperature. Patching compounds can be textured to blend with existing surfaces.

After the work is completed, a professional installer is required by law to leave a certificate that specifies how much material was installed, how many square feet it covered, type of material used, date of installation, and the installer's name. To prevent settling of material (that could result in voids or gaps), contractors install more insulation in each cavity than will it holds at settled density. For example, cellulose will settle to a density of 2.3 pounds per cubic foot, but your contractor should press more than 3.0 pounds into every cubic foot. The possibility of settling is then greatly reduced.

www.homeinspectionservices.org

Category:
��
5:20 PM | Posted in

"High-tech" toilets

Automatic toilet designed to deter drug users

Advanced technology is being integrated into toilets with more functions, especially in Japan (see Toilets in Japan). The biggest maker of these toilets is TOTO. Such toilets can cost anywhere from US$200 to $5,000. The features are operated by control pads (sometimes with bilingual labels), and even hand-held remote control devices. Some of these features are

  • Automatic-flushing mechanisms, operated by a photocell or other sensor. Typically these flush a toilet when the user stands up, or flush a urinal when the user steps away.
  • Water jets, or "bottom washers" like a bidet, as an alternative to toilet paper
  • The "Portable Washlet", Toto's portable hand-held bottom washer
  • Blow dryers, to dry the body after use of water jets
  • Artificial flush sounds, to mask noises such as body functions
  • Urine and stool analysis, for medical monitoring. Matsushita's "Smart Toilet" checks blood pressure, temperature, and blood sugar.
  • Digital clock, to monitor time spent at the toilet
  • Automatic lid operation, to open and close the lid
  • Heated seats (some of which may overheat)
  • Deodorizing fans
  • Automated paper toilet-seat-cover replacers, which automatically replace a paper toilet-seat cover with the push of a button.
  • Electric Toilet Brushes
  • Invented in Australia in 1980, and available in more than thirty countries, are dual flush toilets, also known as duosets. Two buttons allow for the user to select between a flush for urine or feces. Because the density of urine is nearly equal to that of the water around it, it requires far less water to flush into a home's sewage system. Because most of a households' flushes are for urine, dual flush toilets can save a significant amount of water.
Category:
��
4:23 PM | Posted in
In a so-called Clean or technical power system, an isolation transformer with a center tap is used to create a separate supply with conductors at a balanced 60 volts with respect to ground. Unlike a three-wire distribution system, the grounded neutral is not distributed to the loads; only line-to-line connections at 120 volts are used. A balanced power system is only used for specialized distribution in audio and video production studios, sound and television broadcasting, and installations of sensitive scientific instruments. The purpose of a balanced power system is to minimize the noise coupled into sensitive equipment from the power supply. In the United States the National Electrical Code provides rules for such installations.
Clean Technical power systems are not to be used for general-purpose lighting or other equipment, and may use special sockets to ensure only approved equipment is connected to the system.

www.homeinspectionservices.org
Category:
��